Velocity Edge GX325 Manual do Utilizador descarregar pdf (Página 22)

Gaskets—Glueless

SUPERLOCK

Functionally, Tranter’s patented SUPERLOCK

glueless gaskets

perform in the same manner as glued gaskets (see Figures 30, 31

and 32). SUPERLOCK’s unique lock-in design allows simple

installation and removal without glue. The gasket has tabs that

press easily into the holes in the plate. Please note that the

differences between glueless gasket plate assemblies and glued

gasket plate assemblies do not allow for the use of a glued gasket

on a SUPERLOCK style plate. The use of a glueless gasket on

a plate requiring a glued gasket is also incorrect. (NOTE: the

D, E and any special turning plates will be standard spot-glued

gasketed.) The SUPERLOCK design is indicated by replacing

the “X” in the model number with an “M” for a mechanically

attached gasket. It is available in the following models: UMP-

005, UMP-010, UMP-060, UMP-200, UMP-400, GMP-026

and GM-010.

Clip-On

Tranter’s Clip-On glueless gaskets also perform in the same

manner as glued gaskets.The unique design allows easy and

fast clip-on installation without glue or tools, as well as simple

removal. Positive gasket seating and lock-in eliminates assembly

uncertainties. After inspection, undamaged gaskets can be

reused.

The Clip-On gasket system is available in NBR and EPDM, both

industrial and FDA ratings. The Clip-On design is available in

the following models: GMP-026, GC-8, GC-026, GX-26, GX-

42 and GL-13. Four of these models—GC-8, GX-26, GX-42

and GL-13—are interchangeable plates, and can be used with

either glued or Clip-On gaskets.

PLATE NO. GASKET PLATE CLIPPING HANGING

1 NBR (S) H0230 RC START B

2, 4, 6, 8, 10 NBR (S) H1234 LG E

3, 5, 7, 9, 11 NBR (S) H1234 RC B

12, 14, 16, 18 NBR (S) H1234 LG GE

13, 15, 17, 19 NBR (S) H1234 RC CB

20 NBR (S) H1234 LG G

21 NBR (S) H1004 RC END C

22 NBR (S) H1004 PARTITION

23 NBR (S) H1004 RC START B

24, 26, 28, 30, 32 NBR (S) H1234 LG E

25, 27, 29, 31, 33 NBR (S) H1234 RC B

34, 36, 38, 40 NBR (S) H1234 LG GE

35, 37, 39, 41 NBR (S) H1234 RC CB

42 NBR (S) H1234 LG G

43 NBR (S) H0230 RC END C

Model: GXD-042; Plate Material: 304 SS; Plate Thickness: 0.5 mm.

Table 8

Typical Clip-On Gasket Installation

Plate No.: Indicates plate number if single number is given.

Indicates a numerical sequence pattern if multiple numbers are

given. If multiple letter codes are given in the Hanging column, an

alternating sequence between the two letters should be followed

as indicated in the Plate No. column.

Gasket: Deﬁnes the gasket material.

Plate: A ﬁve-digit identiﬁer, which describes plate theta as being

“H” high or “L” low, is followed by four integers. These four

integers indicate which ports are pierced. A zero (0) denotes NO

piercing at this port location.

Clipping: An eight-character ﬁeld describing how the gasket is

to be clipped to the plate. The ﬁrst letter describes whether the

closed port (ringed gasket corner) is in the Lower Right or Lower

Left. Therefore, “R” is Right and “L” is Left. The second letter

denotes the plate letter code. Both of these descriptions apply

when the plate is viewed upright with the designated letter code

being read left-to-right in the upper right hand quadrant of the

plate. Gaskets will be clipped to the front of plate as viewed in

their installed orientation from front-to-back of the assembled

unit. “Start” or “End” can be added to the ﬁrst two-letters with

a space between to denote special gasketing instructions for the

ﬁrst and last plates between end-frames and/or partition plates.

Hanging: Indicates the letter code by which a plate is to be hung

in the unit. This letter should be located in the upper right of

the plate and read from left-to-right. The plate should be viewed

as if from looking from the front of the unit.

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 47 48

Comentários a estes Manuais

Sem comentários

Velocity Edge GX325 Manual do Utilizador Página 22

Comentários a estes Manuais

Manuais e produtos relacionados com Barebones PC/estação de trabalho Velocity Edge GX325